How do you fix a motorcycle throttle cable?

How do you fix a motorcycle throttle cable?

What happens if throttle cable breaks? When the gas pedal is pressed, the cable is pulled and opens the throttle. If the cable breaks, or comes out of adjustment far enough, it can affect the drivability of the vehicle to the point where the car will not be drivable until the problem is addressed.

Are throttle cables universal? In today’s modern vehicles, throttle cables are obsolete with the widespread use of drive-by-wire throttle pedal assemblies. Our universal throttle cable offerings fit most any application or engine type and mounting location.

What causes a motorcycle throttle to stick? A sticky throttle could be caused by worn cables, lack of lubrication in the cables or the cable getting bound up somewhere in the mechanism. Or it can be caused by an issue with the carburetor or EFI. If the screws in the throttle housing are too tight it could cause the cable to stick.

How do you fix a motorcycle throttle cable? – Related Questions

What is the best way to help others see your motorcycle?

Wave at drivers. The best thing to do to help others see your motorcycle is to keep your headlight on at all times. Motorcycles sold in the United States after 1978 automatically have the headlight activated while running, but be sure that the headlight works properly before every ride.

Why do some motorcycles have two throttle cables?

If a throttle return spring breaks, the second cable actively shuts the throttles, saving you an unplanned launch into space.

How do I stop my throttle cable from fraying?

Super Glue will stop the cable from fraying too. One drop on the end, and hit it with activator.

Can you extend a throttle cable?

PowerMadd Black Throttle Cable and Extension helps to add a little extra throttle cable. The throttle extension will extend the throttle cable by 10 inches. The in-line adjuster allows you to fine tune the cable tension and slack. The universal end fits most sleds.

How long do throttle cables last?

How long you can expect your accelerator cable to last will depend in large measure on how often you drive. The more use the accelerator cable gets, the more prone it is to wear and tear. Usually, you can expect to get five years from your accelerator cable before it needs to be replaced.

How tight should throttle cable be?

The accelerator cable tension is usually set so that 2-3mm of free play is present in the throttle grip. Once the correct tension has been applied, the lock nuts should be snugged and any dust covers should be slid back over the adjusters. Cables can be adjusted using the appropriate size wrench.

Can I use wd40 to lube throttle cable?

Choosing The Correct Lubricant

Some cables have a slick inner sheath that will gum up if exposed to solvents or harsh chemicals, so do NOT use WD-40 or any other type of penetrating oil. Regular motor oil works great if you don’t have an appropriate aerosol product.

How do you unstick a throttle?

Pour penetrating oil into the cable (Photo 1). Grab the inner cable with pliers and work it up and down to loosen it. When the cable moves freely and all the penetrating oil has drained out, squirt silicone lubricant into the funnel to keep the cable sliding freely. Reinstall the cable (Photo 2).

Which condition would need to be corrected before you start your motorcycle?

Make sure both tires are in good condition before starting a ride. Ensuring there are no embedded objects and bulges, and monitoring the wear of your tires may contribute to a safer ride. It’s also a good idea to check your tire pressure, especially when it’s cold outside, to make sure they have enough air.

Can you brake while turning motorcycle?

Trail braking is a driving and motorcycle riding technique where the brakes are used beyond the entrance to a turn (turn-in), and then gradually released (trailed off). Depending on a number of factors, the driver fully releases brake pressure at any point between turn-in and the apex of the turn.

Do you need to lube new throttle cables?

If throttle action feels gritty

If the throttle action feels rough or sticky, the throttle tube and/or throttle cables may need lubrication. Interestingly, some workshop manuals specify lubricating these components as part of regular maintenance, while others only mention it as a remedy for improper operation.

Which type of grease is used to lubricate cables?

Asphaltics are the coating type. Various types of greases are used for wire rope lubrication. These are the coating types that penetrate partially but usually do not saturate the rope core. Common grease thickeners include sodium, lithium, lithium complex and aluminum complex soaps.

Why is my motorcycle not accelerating?

Poor acceleration or hesitation may be a sign that your spark plug is worn or dirty or the incorrect type of plug is being used. Examples of poor acceleration include an absence of response or a delayed reaction when you twist the hand throttle or shift the thumb lever.

How does throttle work on motorcycle?

The throttle controls how much air is allowed to flow through the carburetor, and the flow of air is what controls how much fuel is also fed into the engine. This drop in air pressure draws fuel up and out of the carburetor bowl through a series of precisely machined jets and passages, and into the cylinder head.

Are all throttle cables the same?

Usually the push and pull cables are different lengths, and only the pull cable can be adjusted. More importantly, the fittings for the push and pull cable are different. If you need to buy new cables, make sure to buy two different cables instead of two of the same kind, since they aren’t interchangeable.

Are throttle and idle cables the same?

They are not interchangeable. The difference isn’t just the spring, the part that presses into the housing on the handlebar is a different size too for each cable, they only go in one way, so you can’t replace a throttle with a idle or and idle with a throttle cable.

Can you trim throttle cable?

The best way is wrap a bit of tape on it, mark the cut, then use the thinest cut off wheel ya got on it. After the cut carefully unwrap the tape and slid it in the fitting and tighten the allen screw. Done and simple.

Can you solder throttle cable?

Heat the cable end with a torch to get it up to temp quick and put as little heat into the cable as possible. Touch the solder to the cable end to melt it, don’t melt it with the torch or you’ll just get blobs everywhere and they won’t stick to the base metal because it’s not hot enough.