What is a drain wrench?

What is a drain wrench? Innovative, patented design to install and remove tub drains without scratching fine finishes. The only tool of its kind that can be turned with a 3/8” or ½” ratchet wrench and extension from either end. Will also remove or install ½” square plastic toilet seat nuts.

What can I use if I don’t have a drain wrench? Short of a plug wrench, the best substitute is a set of needle-nose locking pliers. The pliers need to be small enough to reach into the drain and through the cross. Once the locking pliers are secured, you use a pair of standard pliers to turn the locking pliers and loosen the drain.

What is a drain key tool? The Superior Tool 4500 Drain Key allows you to unlock and install new drains into your bathtub. It has an expanding design that internally grips to the drain in a 360-degree pattern, making it easy to unlock your drains and remove them.

Can I use pliers instead of a wrench? Although pliers can be used to tighten and loosen nuts, this is a task better suited to the wrench. Pliers tend to damage the surfaces of fasteners and are usually more difficult to use than a properly-sized wrench.

What is a drain wrench? – Related Questions

How much does it cost to tighten a bathtub drain?

Once the flange is carefully threaded into the first few threads of the drain elbow, use the Smart Dumbell to hand-tighten the flange into the drain elbow until tight. Then use your wrench to tighten, by one quarter of a turn. Do this carefully, so as not to squeeze the gasket underneath the tub out of place.

How does a trip lever drain work?

A bathtub with a trip-lever drain stopper works using an internal plunger that moves up and down inside the waste-and-overflow tube to pivot a drain stopper in the drain opening. When the plunger is down, it presses down on the stopper lever and forces the stopper up into the open position.

What is the best tool to unclog a tub drain?

Try a Plumber’s Snake. A plumber’s snake is a handy clog-removing tool you can find at almost any hardware store. Push the snake down the drain slowly until you think you have reached the clog. Start turning the handle of the snake until you bring it back up and out of the drain.

Are all tub drains the same size?

Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep. They are this size because they must fit the opening of the P-trap — also 1 1/2 inches wide — which is a special pipe that has a sharp bend in it.

What’s the difference between pliers and a wrench?

Wrenches are designed to fit nuts, bolts and other standard fasteners. Pliers grip, turn, squeeze and rotate round or irregularly shaped objects of most any size, from baling wire to barbecue grills.

Should you normally pull on a wrench?

Always pull, rather than push, a wrench for greater control and balance. That way, if the nut or bolt should suddenly loosen, you’re less likely to go flying. Never try to get more torque from a wrench by using a cheater bar or other device to extend the leverage.

What’s the difference between a socket wrench and a ratchet?

Sockets are tools that attach to a rachet, torque, or socket wrench. It’s used mostly for loosening and tightening fasteners such as nuts and bolts. Once it’s secured to the ratchet the user can loosen or tighten a bolt or nut while the socket remains in place by just turning the handle of the ratchet.

Which way do you twist a P-trap?

Unscrew the nuts holding a plastic P-trap by hand, gripping the trap firmly with one hand and rotating each nut counterclockwise. You must unscrew two nuts to remove the trap.

What is the difference between a J bend and a P-trap?

The J-bend beneath the sink is also referred to as the P-trap, the U-bend and sometimes even just the drain trap. In some cases, however, hand-tightening may not seat the washer correctly, particularly if your drain pipes are metal, so slip-joint pliers will often come in handy.

Can you over tighten a bathtub drain?

Yes. There’s an epidemic of upstairs tub and shower leaks in my area. Quite a few of them are from over-tightened tub drains. For sure, one of the problems is the cheap-ass washer that often comes with the waste and overflow.

How tight should a shower drain be?

The top of the Pipe should be no higher than, and no more than 1/8″ lower than, the top surface of the floor on which the base will be set. Hand-tighten Drain Nut, and then tighten the rest of the way (about 1/2 turn) with a wrench.

Should trip lever be up or down?

Trip-Lever Stoppers

When the lever is up, the stopper is held in place, keeping your tub filled with water. When the lever is moved down, the stopper lifts and the tub drains.

How do you unclog a trip lever drain?

1). Slowly withdraw the trip waste mechanism and plug from the overflow pipe. Clear hair from the mechanism and run hot water down the train to flush away any debris. Then, open the trip lever on the cover plate, and feed the lever and plug back into the overflow pipe.

How do you fix a cracked bathtub drain?

There may be some plumber’s putty in the drain, and you can get this out with a scraper or putty knife. Get a piece of sandpaper and sand the crack plus 1 inch on all sides around it. Remove any other debris in the area, clean the area well and dry it thoroughly.

What breaks down hair in a drain?

Bleach can dissolve any fiber that has acidic properties. Next time you have a bathroom sink, shower, or bathtub draining slow try pouring a cup of liquid bleach into the drain. After about a half hour any hair the bleach is in contact with will dissolve. Bleach dissolves hair and it takes a bit of time.

Will a drain snake go through a trap?

It is very hard to force a drain snake cable through the bends of a fixture P-trap underneath a sink or tub, but many people try to get through the trap with the cable straight down the drain opening.

Why is my bathtub drain corroding?

This is often due to having a leaking overflow or drain gasket that is seeping water around the steel tub causing it to rust out around the tub drain or overflow.

What size is the toilet drain pipe?

The standard size of a toilet drain pipe is 3 inches in diameter, but the drain can be up to 4 inches in diameter. The drain pipe is usually connected to a 3-inch schedule 40 toilet drain pipe.

Does bathtub need P-trap?

P-traps are S-shaped pipe components that keep toxic sewer gases from escaping into your residence. They are required on all plumbing fixtures, including sinks, tubs and showers. Toilets have built-in traps. Tub and shower traps usually aren’t accessible, however, so they are designed to be permanent.

Should I use a wrench or pliers?

Unlike pliers, wrenches generally do not have pivoting jaws (an exception is the sink wrench). Wrenches are almost always a better tool than pliers for loosening and tightening nuts and bolts because they provide greater torque than pliers and are less likely to round or damage fasteners.

What is the purpose of a wrench?

Wrenches are made in various shapes and sizes and are used for gripping, fastening, turning, tightening and loosening things like pipes, pipe fittings, nuts and bolts.