Why do you need a jointer and a planer?

Why do you need a jointer and a planer?

Is a jointer and planer worth it? A stationary, floor-mounted jointer is even better than a benchtop one because it allows you to work with longer pieces of wood and (in some cases) wider pieces of lumber. One of the biggest challenges people have is getting a jointer to keep cutting properly over time.

Do you really need a jointer? Simply purchase your lumber already milled in S3S or S4S form (surfaced on three sides or surfaced on 4 sides). If you’re at a point in your woodworking where you’re starting to use rough sawn lumber, say from a lumber mill or your local sawyer, then a jointer is absolutely essential to your shop workflow.

Can a planer work as a jointer? A planer can be used as a jointer by following a few woodworking tricks. Woodworking jointers and planers are used to mill wood so they can be used to build furniture and other projects to correct dimensions.

Why do you need a jointer and a planer? – Related Questions

What is the difference between jointer and planer?

A jointer creates a flat surface on wood, and yes, it can be used to correct bow and warp on one side of a board at a time. “A planer is a thicknesser. In other words, you put a board into the planer to make it thinner after you have already established one flat side using the jointer (or a hand plane.)

Is a thickness planer worth it?

If you really want to get into woodworking, a thickness planer is worth the cost. Once you have it, you’ll never regret the expenditure, because you’ll be in control of your stock thickness like never before. A fellow member might be willing to thickness-plane some stock for you for little or nothing.

How important is a jointer?

Rob Johnstone: Jointers are versatile and important tools for stock preparation and shaping. A jointer, properly set up and used, will allow you to create a dead straight edge on a piece of lumber … which makes for a good glue joint or a straightedge to rip from on your table saw.

Can I use a table saw instead of a jointer?

Using Your Table Saw as a Jointer. Even if you own a jointer, you’ll want to master this technique. With the addition of a simple shop-made fence, you can easily edge joint on your table saw.

What can I use instead of a jointer?

Face jointing is where the jointer sings. Face jointing is the first step of a milling a board and is picking the appropriate face and making it flat, the rest of the milling process will reference off of this face. The easiest substitute for face jointing is a planer with a jointing sled!

Can you run a 2×4 through a planer?

Planing 2×4’s won’t help you unless you flatten them on a jointer first. All you would be doing is making the wood thinner. Then if you used a hand held planer you would end up with all different thicknesses which would give you far more problems than not planing the boards at all.

Can you plane the edge of a 2×4?

No, it works fine. Knots in the edge may be a problem, so keep the depth of cut shallow. You might want to joint one edge first, before you plane the other edge. Also be aware of potential or probable snipe on each end of your 2by and allow for the two ends with the snipe to be cut off.

Can you use a planer to fix warped wood?

In order to flatten a warped, twisted, or cupped board, a common approach is to first use a jointer to create one perfectly flat face. Then you run the board through a thickness planer with the flat face downward, and the planer makes the top face parallel to the bottom.

Can you use a planer as a sander?

Whereas sanders are used to alter the finish of wood, a wood planer is used to even out wood to an exact thickness. Planers produce boards of even thickness. With a planer you can smooth rough lumber, clean up sawn edges and give new life to old wood.

What is the purpose of a planer?

A thickness planer (also known in the UK and Australia as a thicknesser or in North America as a planer) is a woodworking machine to trim boards to a consistent thickness throughout their length and flat on both surfaces.

How much can a planer take off?

Most planers remove a maximum of 3 mm per pass. If a narrow piece of lumber is being planed, the maximum amount may be removed. A piece that it at the maximum width of the planer may cause the motor to overheat and the cutter to stall.

What can I do with a thickness planer?

Smooth rough lumber, clean up sawn edges and reclaim salvaged boards with a wood planer. Learn to use a bench-top wood planer correctly and avoid common problems like tearout, snipe and ridges. Reclaim old wood, clean up inexpensive rough-sawn boards, and create custom thicknesses for woodworking projects.

Can a drum sander replace a planer?

Drum sanders are great for fine surfacing or sanding wood, especially figured woods that tear out under planer blades, but it is not the best tool for removing large amounts of wood, such as you would do when leveling glued up boards or surfacing stock.” A drum sander is not made for the rigors of abrasive planing.

How wide does a jointer need to be?

My preference is a jointer with a bed 8-inches wide or wider. An 8-inch wide jointer allows me to joint wider boards than a 6-inch jointer, and 8-inch jointers usually come with longer infeed and outfeed beds, adding more support to the lumber.

Can you use a table saw as a planer?

Simply run the board through the table saw to remove the 1/16″ or 1/32″. Make sure you hold the board as tight against the fence as possible and be careful with the blade up so high. Use push sticks and pads, keeping your hands away from the blade after starting the cut.

Are Rikon planer any good?

Rikon is one of the few companies offering helical head cutters in the 13″ size. So far, the performance is excellent and is easy to use. I am happy with the purchase and would recommend it for anyone who is regularly planing hardwoods and doesn’t have space or budget for a free standing, larger unit.

Why is a jointer called a jointer?

The jointer derives its name from its primary function of producing flat edges on boards prior to joining them edge-to-edge to produce wider boards. The use of this term probably arises from the name of a type of hand plane, the jointer plane, which is also used primarily for this purpose.

Can you join wood without a jointer?

For this method, you’ll need a straight-edge that will ride against the table saw fence. Using tape (preferably double-sided or carpet tape), affix the board to be jointed to the straight-edge. Stagger the boards so that only the straight-edge will contact the fence.

What is the best corner joint for wood?

A bridle joint can be considered a cousin to mortise-and-tenon and is a strong and attractive wood corner joint for frames. The tenon is one-third of the board’s thickness and it slips into the mortise made at the end of a second board to form the rigid corner of a frame.

How do you remove rounded edges from a 2×4?

You don’t need a jointer to remove the rounded corners of a 2×4. You can do it with any tablesaw. Just make sure that you start with the straightest boards you can find. For the best results, crosscut the studs to the needed lengths before ripping the edges.